FabSwingers.com > Forums > The Lounge > Changing thermostatic shower cartridge
Changing thermostatic shower cartridge
Jump to: Newest in thread
|
By (user no longer on site) OP
over a year ago
|
The one on my shower panel has packed up, and have ordered one with the aim to change it myself.
Managed to take down the panel last night and had a good look, and discovered the importance of turning off the water supply prior to doing any work on it.
Need to get the right tools like a suitable size spanner and screw driver, clips for the hoses etc.
It does not look too difficult to take out the temperature and flow assembly, just need to dismantle the faucet and flow regulator in the front.
I shall remember to cover the waste outlet to prevent the nuts and screws from being lost.
I believe I have it all covered, based on my research using the web last night.
Until it is fixed next Wednesday, it will be lukewarm hair washing using the hand held shower spray, and clothe-washing using the sink or bidet.
Wish me luck with my DIY attempt, and any advice from residence plumber will be much appreciated.
|
Reply privately, Reply in forum +quote
or View forums list | |
|
By (user no longer on site)
over a year ago
|
"The one on my shower panel has packed up, and have ordered one with the aim to change it myself.
Managed to take down the panel last night and had a good look, and discovered the importance of turning off the water supply prior to doing any work on it.
Need to get the right tools like a suitable size spanner and screw driver, clips for the hoses etc.
It does not look too difficult to take out the temperature and flow assembly, just need to dismantle the faucet and flow regulator in the front.
I shall remember to cover the waste outlet to prevent the nuts and screws from being lost.
I believe I have it all covered, based on my research using the web last night.
Until it is fixed next Wednesday, it will be lukewarm hair washing using the hand held shower spray, and clothe-washing using the sink or bidet.
Wish me luck with my DIY attempt, and any advice from residence plumber will be much appreciated.
"
Good for you and good-luck....... |
Reply privately, Reply in forum +quote
or View forums list | |
|
By (user no longer on site)
over a year ago
|
"The one on my shower panel has packed up, and have ordered one with the aim to change it myself.
Managed to take down the panel last night and had a good look, and discovered the importance of turning off the water supply prior to doing any work on it.
Need to get the right tools like a suitable size spanner and screw driver, clips for the hoses etc.
It does not look too difficult to take out the temperature and flow assembly, just need to dismantle the faucet and flow regulator in the front.
I shall remember to cover the waste outlet to prevent the nuts and screws from being lost.
I believe I have it all covered, based on my research using the web last night.
Until it is fixed next Wednesday, it will be lukewarm hair washing using the hand held shower spray, and clothe-washing using the sink or bidet.
Wish me luck with my DIY attempt, and any advice from residence plumber will be much appreciated.
"
Just got a semi reading all that technical stuff from a lady |
Reply privately, Reply in forum +quote
or View forums list | |
"Thanks Soxy, and the need to disconnect from the water supplies is already on the list as the first thing to do after taking down the panel. "
Are you sure there isn't a valve allowing you to isolote the supply?
Generally looks like a screw thread with is on the mains pipe feed and is purely a half turn to switch off - sorry best way i can think of trying to describe it. |
Reply privately, Reply in forum +quote
or View forums list | |
|
By (user no longer on site) OP
over a year ago
|
"Thanks Soxy, and the need to disconnect from the water supplies is already on the list as the first thing to do after taking down the panel.
Are you sure there isn't a valve allowing you to isolote the supply?
Generally looks like a screw thread with is on the mains pipe feed and is purely a half turn to switch off - sorry best way i can think of trying to describe it."
.
Not a single valve, but a screw on each of the hot and cold inlet.
I can always turn off the inlet to the entire house by shutting off the supply using the stop cock under the kitchen sink.
|
Reply privately, Reply in forum +quote
or View forums list | |
|
By (user no longer on site) OP
over a year ago
|
"put a plug in the plughole so if you do drop a screw it won't get lost .. and put an old towel on the tray or bath so you don't scratch it "
.
Already considered covering the waste grill.
Nothing to scratch as it is a wet room and tiled. I shall be standing with my back to the glass panel, like I did when I took the shower panel down to have a look.
Thanks for the advice though.
|
Reply privately, Reply in forum +quote
or View forums list | |
|
By (user no longer on site) OP
over a year ago
|
"Some shower manufactures require a special tool( no I'm not being funny) to remove the cartridge so be careful but good luck."
.
I have contacted the manufacturer for advice, however, I cannot see any special tool being required, as the temperature and flow assembly is a sealed unit.
Just need to dismantle the faucet and the thermostatic control in the front of the panel, unclip/unscrew the hoses that are attached to assembly in order to take it out.
|
Reply privately, Reply in forum +quote
or View forums list | |
"Thanks Soxy, and the need to disconnect from the water supplies is already on the list as the first thing to do after taking down the panel.
Are you sure there isn't a valve allowing you to isolote the supply?
Generally looks like a screw thread with is on the mains pipe feed and is purely a half turn to switch off - sorry best way i can think of trying to describe it.
.
Not a single valve, but a screw on each of the hot and cold inlet.
I can always turn off the inlet to the entire house by shutting off the supply using the stop cock under the kitchen sink.
"
0nly dabbled a little with a shower but i found that the valves are sufficient Pearl on both to isolate the water supply.
I looked on a certain well known site for DIY videos - not sure if i am allowed to mention it but there is a good tutorial and all he used was a standard opened ended wrench.
You seem well prepared good luck and let us all know how you get on.
|
Reply privately, Reply in forum +quote
or View forums list | |
|
By (user no longer on site) OP
over a year ago
|
The replacement part is:
Hudson Reed A398 Temperature and Flow Assembly
Google it and one should be able to see what it looks like.
3 hoses to attach. One is plastic for the water once mixed, and needs to be tightened using a hose grip; the other two are connect to the hot and cold inlets using flexible metal hoses, and I need to buy the right size wrench for it, as the one I use for my bike maintenance is too small.
I struggled to dismantle the thermostatic control until I watched some vids on the net for similar issues, and managed to find the concealed screw that was holding the housing in place. So the WWW did help!
|
Reply privately, Reply in forum +quote
or View forums list | |
|
By *nnyMan
over a year ago
Glasgow |
"...........
Wish me luck with my DIY attempt, and any advice from residence plumber will be much appreciated.
"
I'm not a plumber but I like to take things apart.
I now take photographs of each stage of the dismantling. Makes it easier to put things back together.
Good luck. |
Reply privately, Reply in forum +quote
or View forums list | |
"The replacement part is:
Hudson Reed A398 Temperature and Flow Assembly
Google it and one should be able to see what it looks like.
3 hoses to attach. One is plastic for the water once mixed, and needs to be tightened using a hose grip; the other two are connect to the hot and cold inlets using flexible metal hoses, and I need to buy the right size wrench for it, as the one I use for my bike maintenance is too small.
I struggled to dismantle the thermostatic control until I watched some vids on the net for similar issues, and managed to find the concealed screw that was holding the housing in place. So the WWW did help!
"
You could always get an adjustable wrench i'm certain they still make them.
If i lived closer would let you borrow mine |
Reply privately, Reply in forum +quote
or View forums list | |
|
By (user no longer on site) OP
over a year ago
|
"
You could always get an adjustable wrench i'm certain they still make them.
"
.
I'll be getting an adjustable spanner of the appropriate size, yes.
|
Reply privately, Reply in forum +quote
or View forums list | |
"
You could always get an adjustable wrench i'm certain they still make them.
.
I'll be getting an adjustable spanner of the appropriate size, yes.
"
Perfect if not a rather nice plumber to assist |
Reply privately, Reply in forum +quote
or View forums list | |
Have spoken to my brother-inlaw who`s a plumber of 37 yrs and he`s says you seem to know you have made sure of what to do ok,ie water off,electric off and all the right tools.So just take your time an every things should go well. |
Reply privately, Reply in forum +quote
or View forums list | |
|
By (user no longer on site) OP
over a year ago
|
"Have spoken to my brother-inlaw who`s a plumber of 37 yrs and he`s says you seem to know you have made sure of what to do ok,ie water off,electric off and all the right tools.So just take your time an every things should go well."
.
Thanks for checking with your bro-in-law the plumber.
And thanks everyone for your good wishes! |
Reply privately, Reply in forum +quote
or View forums list | |
|
By (user no longer on site) OP
over a year ago
|
Quick update, I have finally succeeded in changing the temperature and flow assembly on my shower panel.
Needed to get more tools, and a lot of patience and quite a bit of strength.
However, I have done it, and celebrated with a piping hot shower, naturally.
Feeling very smug for having done it all by myself.
It is a significant milestone, as I am determined to do more DIY on the house without resorting to external help next year.
|
Reply privately, Reply in forum +quote
or View forums list | |
» Add a new message to this topic